Wrist joints help?

Need help getting your custom completed? Looking for your next idea? Do you need some new tips or suggestions to complete your project? Come chat with us!

Moderator: Regulators

Wrist joints help?

Postby trekking95 » Mon Jun 11, 2012 3:15 pm

Well as we all know The Avengers figures have no wrist joints. There are a few other joints they don't have but I think the wrist is the most important since you can get better poses with them holding their weapons.

So is there a way to make wrist joints? Like somehow cut off the hands and stick them back on with a peg?
A way to fix broken wrist joints on figures that have them could likely be used here.

Thanks!! :)
User avatar
trekking95
Inductee Realmer
 
Posts: 49
Joined: Fri May 18, 2012 10:59 pm

Re: Wrist joints help?

Postby trekking95 » Wed Jun 13, 2012 1:01 am

Seriously, someone must know something about this! This is a custom figure site after all!!!

And yes, I looked in the tutorials area. All the joint stuff I could find was for the 6 in. figures. The joints on 3.75 in. figures are too small for those ways of doing it.
User avatar
trekking95
Inductee Realmer
 
Posts: 49
Joined: Fri May 18, 2012 10:59 pm

Re: Wrist joints help?

Postby cosmicfantasycustoms » Wed Jun 13, 2012 1:13 am

revoltech joints could help. check out countpichula's thread in the custom workstation to see them in action. if you are talking about 3.75 inch figs, you might have to go and buy a revoltech figure, which are not cheap. but you can get a set of the joints off of ebay. hope this helps.
User avatar
cosmicfantasycustoms
Regulator
 
Posts: 2016
Joined: Mon Jan 03, 2011 4:41 pm
Location: http://www.figurerealm.com/forums/viewtopic.php?f=25&t=40241

Re: Wrist joints help?

Postby trekking95 » Wed Jun 13, 2012 3:10 am

cosmicfantasycustoms wrote:revoltech joints could help. check out countpichula's thread in the custom workstation to see them in action. if you are talking about 3.75 inch figs, you might have to go and buy a revoltech figure, which are not cheap. but you can get a set of the joints off of ebay. hope this helps.

Are the joints small enough for the 3.75 in. figures? The ones I saw on eBay look like they have a large ball joint in the center.
User avatar
trekking95
Inductee Realmer
 
Posts: 49
Joined: Fri May 18, 2012 10:59 pm

Re: Wrist joints help?

Postby cosmicfantasycustoms » Wed Jun 13, 2012 4:33 pm

you may need to pick up a revoltech fig for some of the joints for those figs. the ones in the pack are for larger figs and might not look proper on that size of figure.
User avatar
cosmicfantasycustoms
Regulator
 
Posts: 2016
Joined: Mon Jan 03, 2011 4:41 pm
Location: http://www.figurerealm.com/forums/viewtopic.php?f=25&t=40241

Re: Wrist joints help?

Postby kadenscott » Thu Jul 12, 2012 1:41 am

cosmicfantasycustoms wrote:revoltech joints could help. check out countpichula's thread in the custom workstation to see them in action. if you are talking about 3.75 inch figs, you might have to go and buy a revoltech figure, which are not cheap. but you can get a set of the joints off of ebay. hope this helps.


Thanks for the help. :)
Kaden Scott
kadenscott
Newbie Realmer
 
Posts: 1
Joined: Thu Jul 12, 2012 1:36 am


Return to Custom Help / Questions / Info

Who is online

Users browsing this forum: No registered users and 2 guests


cron