LEDs and Battery connection

Need help getting your custom completed? Looking for your next idea? Do you need some new tips or suggestions to complete your project? Come chat with us!

Moderator: Regulators

LEDs and Battery connection

Postby Beautifuldone » Tue Dec 17, 2013 1:05 am

Greetings Customizers and Toy Lovers,

I'm working on a custom for myself at the moment. It's my first custom ever. I decided to take apart one of my favorite figures to try to make it look a little better and add some style, but I'm stuck.

I need a mini motor, 4 led lights and a switch in a series circuit. I managed to pull off the 4 lights and got those working, but the motor and switch would not work. Does anyone have a way this could work? It was my first time doing LEDs and soldering. I'm clearly not a professional, but I'd very much appreciate if someone could help me out.

It looked like this:

Battery---Negative wire--- motor ---resistor---led---led---led---led---positive wire--switch---positive wire---back to battery.


With that setup the light only worked after taking the switch off. Any help out there from someone who knows what they are doing?

Thank you kindly,
Beautifuldone
Beautifuldone
Newbie Realmer
 
Posts: 3
Joined: Tue Dec 17, 2013 1:03 am

Re: LEDs and Battery connection

Postby Pock63 » Tue Dec 17, 2013 9:52 am

What are you using the mini motor for? and how big is it?
You'll be lucky if you're one of the few to find someone who can tolerate you.
Image
User avatar
Pock63
Realm Addict
 
Posts: 3871
Joined: Thu Jun 26, 2008 11:58 am

Re: LEDs and Battery connection

Postby Beautifuldone » Tue Dec 17, 2013 10:24 am

This is the motor:

http://www.amazon.com/gp/aw/d/B009IN0AUU

Which I'll be putting in the Neca 7 inch Gypsy Danger. My goal is to make his reactor spin. Everything is carved out for the motor to fit inside with a battery pack as well, but the problem is connecting it all.

These are the switches:
http://www.amazon.com/gp/aw/d/B006S21U2 ... 1?pi=SS115


I should have went into more detail earlier :)
Beautifuldone
Newbie Realmer
 
Posts: 3
Joined: Tue Dec 17, 2013 1:03 am

Re: LEDs and Battery connection

Postby Beautifuldone » Tue Dec 17, 2013 10:47 am

I'm also looking on how to connect those switches. They have 6 little metal prongs on them so I don't know where to connect them. How to do the lights and soldering I got from Jin's guide which was a god send :)
Beautifuldone
Newbie Realmer
 
Posts: 3
Joined: Tue Dec 17, 2013 1:03 am

Re: LEDs and Battery connection

Postby Redcarl69 » Sat Jan 18, 2014 3:52 pm

Ok this may help, a typical LED will drop about 1.8v across it. Therefore 4 times 1.8v (7.2v) is dropped in this circuit leaving insufficient voltage to drive a 12v motor. The LEDs need to be in parallel, though the resistor size will need amending or you'll over drive the LEDs.
The switch looks like a 2 pole switch, this means both positive and negative can be switched at the same time. The 6 pins will be 2 normally open, 2 normally closed, 2 output. You'll need to test continuity to find which to use, basically meter across 2 pins (no continuity) press the switch looking for continuity (beep etc on your meter). Trial and error until you find which pair of pins to use.
Hope this helps.
Redcarl69
Newbie Realmer
 
Posts: 1
Joined: Sat Jan 18, 2014 3:28 pm


Return to Custom Help / Questions / Info

Who is online

Users browsing this forum: No registered users and 1 guest