![[Freddy Kruger V2] I wanted to make another Freddy Kruger, cause the one I had made previously for a customer was lacking a hat. Freddy needs his hat. So back to the creation room.
Basically the recipe for this Freddy is like the other I made, Only I used a Stone Cold Figure instead of an Edge Figure. Which turned out to be easier, cause I didn't have to worry about removing the hair.
The hat was made using a foam clay.
You can not do this Competition without having Freddy Kruger! He is such a bad dude. Watch his movies! you know he's an A-hole! The man was the Springwood slasher! He is extremely vile!](userimages/customs/9500/9134-1.jpg) Freddy Kruger V2 | ![[Pretty Kitty DeathBot 3000] The future holds no bounds. That is unless you have slipped into the past. Dr. Konqor had done just that. Being from year 3417, not much was a challenge for the good Doctor. Heck, almost everyone was called a doctor, since the perfection of selective breeding was initiated over 1200 years ago. Konqor needed a challenge, and he got it.
His Friend had managed to create a sort of "Time manipulator", which could send one item back to whenever he wanted. He longed for the days when being smart was rare, and feared.
He asked his friend to be the first test subject, and was obligated as well.
They set the time for 1996 AD. After that, it was a hand shake, and off he went.
There were no real theatrics in the transport. Just a couple bright flashes and poof, 1996. Unfortunately, the landing process was difficult. See, when he left, he was at the 2nd story of a building. Now he's about 15 feet in mid air falling into an animal park.
The machine was partially damaged, but he knows he c](userimages/customs/7500/7104-1.jpg) Pretty Kitty DeathBot 3000 Miscby JunkPunkThe future holds no bounds. That is unless you have slipped into the past. Dr. Konqor had done just that. Being from year 3417, not much was a challen...3 comments |
![[Toy Soldier 1st Lt. Keblade Reverend] I didn't need to shave anything down on this figure, just a lot of adding
Recipe:
Cade Murdock Action figure
Fixit Sculpt
Model Magic fusion
17 gauge galvanized electric fence wire
black thread
black 3d paint
Black, red, silver, green, and gold paint
I used the Model Magic Fusion clay for the hang of the pants and shirt, and the hat. I used fixit sculpt for the rest of the shirt, pants, for the goggle lenses, for the soul patch. and patches on the shirt and hat. The thread was at the back of the hat to show the goggles were tied in the back.
The key blade was done with the wire, and fixit sculpt.](userimages/customs/7000/6877-1.jpg) Toy Soldier 1st Lt. Keblade Reverend Miscby JunkPunkI didn't need to shave anything down on this figure, just a lot of adding
Recipe:
Cade Murdock Action figure
Fixit Sculpt
Model Magic fusion
17 gauge...1 comments | ![[TAF Member Psyclone J.] This was originally Was Going to be a Burnt Zombie, But when I heard that Psyclone J had burned his arms in a fireball match, I decided to switch gears.
This is a Custom figure of Team Action Figure Member Psyclone J.
* Pants were made from cloth, with Tulip Paint for the Cammo design
* Mask and Hair and Ponytail was done with Tulip paint
* Shirt was made with tulip paint
* Gloves were made with Tulip paint
* Kendo Stick (Which was named Candi by Psyclone) Was a cut tube of plastic painted with a tan/yellow acrylic paint, and accented with Tulip paint.
* Hands and arms were burned with a Zippo Lighter.
***Nearly the whole darn figure was customized with Tulip paint. This was done before I started using Fixit Sculpt.
Along with the custom pics is a pic of the real indy wrestler in gear. Enjoy!](userimages/customs/6000/5937-1.jpg) TAF Member Psyclone J. Wrestlingby JunkPunkThis was originally Was Going to be a Burnt Zombie, But when I heard that Psyclone J had burned his arms in a fireball match, I decided to switch gear...3 comments |
![[TAF Member Vinny Rattlocke] Okay, I got this Figure at a garage sale back in 05. I looked like a chew toy for a dog. Its hand and hair was chewed off. But I knew I'd model this after an independent wrestler that goes by "The Boat hand" Vinny Rattlocke. He wrestles for leagues in the midwest. He's apart of a stable called Team Action Figure. It is a group for wrestlers that follow Dr. Steel, another figure I've done.
The customizing was fun. The body was a whole repaint. Tulip paint was used for the hair, wristbands, pants accents, facial hair, and accents on the mask.
The mask was made with neon yellow pleather, and glued to the face.
the hardest part was to make the boat for his hand. I waited on this for almost a whole year. Finally I saw a toy at the dollar store that was perfect, but it was a jet. So, I hacked it up and added some Fixit Sculpt and attached it to the hand. Then, used a little more sculpt for the belt buckle, painted it yellow, and added the TAF icon.
Boom, there's vinny.
I have al](userimages/customs/6000/5820-1.jpg) TAF Member Vinny Rattlocke Wrestlingby JunkPunkOkay, I got this Figure at a garage sale back in 05. I looked like a chew toy for a dog. Its hand and hair was chewed off. But I knew I'd model this a...11 comments | ![[Marvel Zombie Beast Feeding Time] I had a couple people tell me that since I like to do horror figures so much, That I need to try my hand at some Marvel Zombies figures. Okay.
I got this Beast figure at a flea market with a couple other figures. So here we go. I dermeled the rib cage, and leg and shoulders, and made the exposed bones in the left arm. I took a Xacto blade and carved into the head. And I separated the right big toe, and skinned it a little.
I used Fixit sculpt to make the blow out in the back of the head, the intestine hanging out of his abdomen, and the intestine in his hand, Used smaller pieces of Fixit sculpt to make loose sking and meat chunk that stuck to his fur. The good eye was blackened, and tulip glow in the dark paint to make it glow, Used several styles of red paint(paint pen, dry brushing, and tulip paint) to make him look like he had several stages of zombie-ism.
One layer of clear acrylic sealer, and he's ready for the buffet.](userimages/customs/6000/5797-1.jpg) Marvel Zombie Beast Feeding Time Zombiesby JunkPunkI had a couple people tell me that since I like to do horror figures so much, That I need to try my hand at some Marvel Zombies figures. Okay.
I got ...3 comments |
![[Doctor Phineas Waldolf Steel Key Club Outfit] This custom Figure Is made in honor of our future world emperor, Dr. Phineas Waldolf Steel.
If you do not know about this man, well, at least the figure can be a start.
I based this figure on the outfit he was waring towards the end of his set at the Key club, a couple years back.
But the figure was another story.
The figure I had gotten last year at a garage sale for a quarter. When I had gotten home, the head broke off. It sat in a drawer, until I discovered Fixit Sculpt. I was able to fix the neck joint with it. Then, I went to work.
I took my dremel, and sanded down the big beard on his face, as well as the legs, cause they looked like football pants. After I sanded it all down, I took more Fixit, and I made the bottoms of the pants bell out, and platforms for the boots. I also used the fixit to make the beard, and goggles that the Good Doctor wears. I also used a wood burner tool to make the mouth.
Then surgery on the left arm. The way the fist was facing was at a weird angl](userimages/customs/6000/5585-1.jpg) Doctor Phineas Waldolf Steel Key Club Outfit Miscby JunkPunkThis custom Figure Is made in honor of our future world emperor, Dr. Phineas Waldolf Steel.
If you do not know about this man, well, at least the fig...0 comments | ![[Ashley J. Williams Post Evil Dead 2 fight.] I really want to come up with a good story line. But if you don't know who this is, GET OUT!!!
I'm a big fan of the evil dead series, and even though this series says "Army of Darkness" It's based on the way he looked at the end of ED2, after fighting rotten apple head.
This was my longest, and perhaps best custom, so far! I took him totally apart. I went and bought some "Fixit Sculpt", and went to town on this guy.
First, the head had a very round top, and a pointy chin. So, I gave him his big hair, and a more distinguished chin with the cleft in it.
next the pants originally stopped at the top of the shoes. So I used the Sculpt to make his pant legs longer, and tattered. And the feet still rotate, as well.
The right hand was removed, and the chainsaw was added, but first...
The chainsaw was originally very thin, with little detail. So, I used the Sculpt to ad the extra side handle,bigger motor, and a pull start chord handle.
I then drilled a small hole in th](userimages/customs/6000/5573-1.jpg) Ashley J. Williams Post Evil Dead 2 fight. Army of Darknessby JunkPunkI really want to come up with a good story line. But if you don't know who this is, GET OUT!!!
I'm a big fan of the evil dead series, and even though...3 comments |
![[Freddy Kruger - Battle Worn] Freddy is pretty worn out after his last battle in the real world. He sits at his work table in his boiler room as he sharpens new claws to replace his broken ones on his last two fingers. He stares at the fresh blood splattered across his body. Some from his victims, and some his own. Wishing he still had his hat, Freddy plots his revenge on the town of Springwood.
This Figure was made from an Edge WWF action figure.
* The legs and head were dremeled down. and a wood burning tool was used to put in the cuts, and scarring, and open mouth grin.
* Sweater was made from an old Halloween costume glove. Wear on Sweater made by an X-Acto blade.
* The Blades from the Claw glove was made from an old gift card that had the shapes cut out, and then the fingers slit, and blades placed in the slits and glued.
* Extra blood and dirt on the body added by use of Tulip paint.](userimages/customs/5500/5391-1.jpg) Freddy Kruger - Battle Worn | ![[Jason Voorhees - Big and Buff] This version was to be made for Jason to look a little more on the buff side. flesh part of the body was painted with my special "Decay" mixture. The shirt was made with some thin blue cloth, glued against the body to look tight, and show off the muscles. the mask and straps were added to the face by way of tulip paint. and the body was splattered with a blood and dirt colors.](userimages/customs/5500/5361-1.jpg) Jason Voorhees - Big and Buff Friday the 13thby JunkPunkThis version was to be made for Jason to look a little more on the buff side. flesh part of the body was painted with my special "Decay" mix...1 comments |
![[Micheal Myers Oldschool] Basically, this figure was mostly painted an all dark blue to make the jumpsuit, and the mask totally done with tulip paint for the rubbery look.](userimages/customs/5500/5143-1.jpg) Micheal Myers Oldschool Halloweenby JunkPunkBasically, this figure was mostly painted an all dark blue to make the jumpsuit, and the mask totally done with tulip paint for the rubbery look....2 comments | ![[Leatherface] Feet were sanded and painted to look like cowboy boots. Cloth added to give a full apron look. 3D paint added to face to give the "Fleshy" mask look.](userimages/customs/5500/5131-1.jpg) Leatherface |
![[Jason Voorhees] This lil' guy was created, cause I didn't want a chewed up edge figure, but I didn't want to just throw it away. So, I sanded it all down, used a dark green costume glove to fashion into a worn shirt. And the mask was made from an old sci fi figure's helmet accessory. The machete was made out of heated up lead poured into a hand carved wood mold. A lot of drilling, sanding, sewing, and painting went in to this guy. And now he'll be up on somebody's shelf, killing Barbie dolls.](userimages/customs/5500/5129-1.jpg) Jason Voorhees Friday the 13thby JunkPunkThis lil' guy was created, cause I didn't want a chewed up edge figure, but I didn't want to just throw it away. So, I sanded it all down, used a dark...4 comments | |
|